HOME > Product Information > 3000 series > 3017

New product list

Product category

Product number list

1000 series

2000 series

3000 series

4000 series

5000 series

5200 series

6000 series

7000 series

7700 series

9000 series

9900 series

Automation equipment

Others

Damper agents

ThreeBond 3017 High peeling-adhesive strength, light curing adhesive

Typical UV-curing adhesives usually don't have sufficient peeling-adhesive strength for soft adherend, especially for adhesion of two sheets of polyester film that is so called a hard-to-adhere material.
ThreeBond 3017 enables polyester films with unprocessed surfaces to have the high peeling-adhesive strength.

·	Has excellent peeling-adhesive strength for films such as polyester.
·	Has excellent peeling-adhesive strength among various plastics, and a plastic and a metal.
·	Has some softness in resin hardness after curing under room temperature.
·	Has low permeability.

·	Bonding of various polyester
·	Bonding among plastics, and a plastic and a metal

1)	Physical properties

Table 1. Physical properties

Test items	Units	Test results	Test method	Remarks
Appearance	-	Yellow and transparent	3TS-201-01
Viscosity	Pa.s	46	3TS-210-05	25°C *1
Specific gravity	-	0.87	3TS-213-02	25°C

*1 EHD Viscometer 3°×R14, Rotation speed: 5rpm

2)	Curves of fluidity and viscosity (Rheometer)


	Figure 1. Curves of fluidity and viscosity

	Figure 2. Temperature - Viscosity curve, Shear rate 1.0 (1/s)

Properties of cured object

1)	Physical properties

Table 2. Physical properties

Test items	Units	Test results	Test method	Remarks
Hardness	-	A 20	3TS-215-01
Permeability	g/m².24h	16.4	JIS Z 0208 (method to use a cup)	40°C, 95% RH 400μm thickness
Glass transition temperature	°C	0	3TS-501-04	DMA method 1Hz, E''peak

Characteristics of adhesive strength

1)	T-type test of peeling-adhesive strength

Table 3. T-type test of peeling-adhesive strength for various films

Measurement ambient: 25°C, 55% RH

Tested materials	Test results (kN/m)	Remarks
PET/PET	1.60	Toyobo. Co., Ltd Ester film E5100 75μm Adhesion to unprocessed surface
PET/PET	1.62	Teijin Limited Teijin Tetron SL-75 75μm
PET/PET	1.42	Toray Industies, Inc. Lumirror S-10 75μm
PET/PET	1.54	Toray Industies, Inc. Lumirror T-60 75μm
PEN/PEN	1.07	Teijin Limited Teonex Q51 125μm
PEN/PEN	1.50	Teijin Limited Teonex Q65 100μm Adhesion to processed surface
PEN/PEN	1.53	Teijin Limited Teonex Q83 75μm
PPS/PPS	1.16	Toray Industies, Inc. Torelina 3030 75μm


Resin thickness:	about 90μm
PEN:	Polyethylene naphthalate
Curing conditions:	30kJ/m²×2
Test method:	3TS-304-21

Table 4. 180-degree peeling test of ahesive strength for various films

Measurement ambient: 25°C, 55% RH

Tested materials	Test results (kN/m)	Remarks
PET film/PET	1.24
PET film/PE	0.54
PET film/PP	0.86
PET film/6-nylon	0.94	Toray Industies, Inc. Amilan CM-1021
PET film/acrylate	2.34	VH000
PET film/Polycarbonate	1.96	Panlite L-1225
PET film/ABS	1.32	Tsutsunaka EAR-003
PET film/Ni	1.66	JIS, G 3141 (SPCC, SB), Nickel plate NFNiL
PET film/Fe	1.19	JIS, G 3141 (SPCC,SB)
PET film/Aluminum	1.11	JIS, H 4000 (A1050P)
PET film/SUS430	1.81	JIS, G 4305
PET film/ZEONEX	1.83	Zeon Corporation ZEONEX: 480R
PET film/ZEONEX	0.81	Zeon Corporation ZEONEX: 330R


PET film:	Toray Industies, Inc. Lumirror S-10 75μm
Resin thickness:	about 90μm
Curing condition:	30kJ/m²×2
Test method:	3TS-304-11

How to use this adhesive

Typical curing conditions: Accumulated luminous energy of ultraviolet 60kJ/m² (6000mJ/cm²), at the environment of 25°C. If you have any question about the curing of this adhesive, consult ThreeBond sales engineers.

Cautions about using this adhesive

1)	Because the curing speed of this adhesive depends on types of light sources and distance of irradiation, confirm these and other conditions before use. Especially the temperatures of the adhesive and the adherends according to the temperature change in the room have a great influence on the curing speed.
2)	Use this adhesive after fully assuring that the method and purpose of your use are adequate.
3)	A forced ventilation is required in the areas of working and UV irradiation, because some gasses are generated during the working and UV curing. If required, wear appropriate protective devices, such as a mask, globes (no penetration allowed), and glasses, and/or use the adhesive in a room with a local exhauster.
4)	Don't inhale vapor of the adhesive or drink it, because it is hazardous to human body. Immediately consult a doctor if you drink it by any chance.
5)	Because this adhesive is hazardous, don't touch it directly. If it adheres to your skin, the skin may be irritated. Immediately remove it with cloth or paper, and clean the skin with soap. If any gets into your eye, clean the eye with water for about 15 minutes, and then consult a doctor.
6)	If you detect any bad symptom on your body when you use this adhesive, stop using it, and consult a doctor. Persons who have allergy or have susceptible skin should not use this adhesive.
7)	On some materials this adhesive may have adverse effects. Test the effect of the adhesive on and around the areas of application, and refrain from using it if you find that it might cause a problem.
8)	Don't move this adhesive to other containers, and don't return any residue of applied adhesive to the container.
9)	To prevent any change of the properties of the adhesive, or the incorporation of foreign materials, recap the container after use.
10)	Use and store it out of the reach of infants and children.
11)	For detailed information, refer to the Material Safety Data Sheet (MSDS).

How to store the adhesive

Store this adhesive at 10°C to 25°C under no sunlight and low humidity.

How to discard the adhesive

	If you need to discard this adhesive, have it discarded by a dealer who has specialized knowledge.
	Don't incinerate the adhesive. If you do so, it may generate poisonous gases.

Cautions

(Don't use this adhesive at home.)

Use this adhesive only after accepting the following sales conditions:
1)	The technical information we present, such as written data, consists of experimental values resulting from tests performed in accordance with our specifications, and we cannot absolutely guarantee its accuracy and integrity. Customers who use this adhesive are expected to judge by themselves, before use, whether this product is appropriate for their use, and to have the full responsibility and risks for the use of the product. Our guarantee extends only to the replacement of any products found to be defective.
2)	ThreeBond cannot take any responsibility for personal injury or property damage that may result from improper use of this product.
3)	ThreeBond cannot take any responsibility for occurrences not specified in this home page, except as specified in a written contract with a customer.